About this job
<h3><strong>About Us</strong></h3><p style="min-height:1.5em">Harmattan AI is a next-generation defense prime building autonomous and scalable defense systems. Following the close of a $200M Series B, valuing the company at $1.4 billion, we are expanding our teams and capabilities to deliver mission-critical systems to allied forces.</p><p style="min-height:1.5em">Our work is guided by clear values: building technologies with real-world impact, pursuing excellence in everything we do, setting ambitious goals, and taking on the hardest technical challenges. We operate in a demanding environment where rigor, ownership, and execution are expected.</p><p style="min-height:1.5em"></p><p style="min-height:1.5em"><strong>Overview</strong><br />Harmattan AI is developing new hardware products within the GCS module, including ruggedised drone controllers and long-range RF systems designed for demanding field environments. These products require dedicated electronics design with complex architecture in a constrained environment – PCBs integrating RF modules, microcontrollers, power management, and communication interfaces – optimised for cost at volume. The GCS team is seeking a dedicated hardware engineer to own electronics design end-to-end and accelerate the path to production milestones.<br /><br /><strong>Ideal candidate</strong></p><p style="min-height:1.5em">A senior hardware engineer who has designed and shipped complex PCBs, ideally mixing digital and power, into production. They are rigorous on schematics, layout, and bring-up, and have a strong instinct for cost and manufacturability. They are comfortable working autonomously in a small team and can bridge hardware and firmware.<br /><br /><strong>Skills required</strong></p><ul style="min-height:1.5em"><li><p style="min-height:1.5em">PCB schematic and layout design (Altium Designer preferred)</p></li><li><p style="min-height:1.5em">RF PCB design: controlled impedance, antenna matching, EMC management</p></li><li><p style="min-height:1.5em">Mixed-signal design: power management, MCU interfaces, communication buses (SPI, I2C, UART, USB, CAN)</p></li><li><p style="min-height:1.5em">Hardware bring-up and debug: bench equipment proficiency</p></li><li><p style="min-height:1.5em">DFM/DFA for PCB manufacturing and assembly</p></li><li><p style="min-height:1.5em">Component selection and BOM management</p><div style="min-height:1.2em;margin-top:0;margin-bottom:0"> </div></li></ul><p style="min-height:1.5em"><strong>Responsibilities:</strong></p><ul style="min-height:1.5em"><li><p style="min-height:1.5em"><strong>Schematic Design</strong> - Design complete schematics for mixed-signal and RF boards, from power to digital and RF sections.</p></li><li><p style="min-height:1.5em"><strong>PCB Layout & Routing</strong> - Perform or lead board placement and routing with attention to signal integrity, EMC, and RF constraints (6-8 layer layout, controlled impedance, ground planes, and RF traces).</p></li><li><p style="min-height:1.5em"><strong>Component Selection & BOM Optimisation –</strong> Select components with cost, availability, and reliability in mind; drive BOM cost reduction for mass production volumes.</p></li><li><p style="min-height:1.5em"><strong>Hardware Bring-up & Debug</strong> - Lead board bring-up and debug issues with oscilloscopes, spectrum analysers, and other bench equipment; write bring-up scripts when needed.</p></li><li><p style="min-height:1.5em"><strong>EMC & RF Compliance</strong> - Address EMC challenges; ensure signal integrity across the board and correct RF performance (antenna impedance matching and power levels).</p></li><li><p style="min-height:1.5em"><strong>Collaboration with Embedded SW</strong> - Work closely with the embedded software engineer to define hardware/software interfaces; support firmware bring-up.</p></li><li><p style="min-height:1.5em"><strong>Collaboration with Mechanical</strong> - Ensure seamless PCB integration into mechanical enclosures (connectors, mounting, thermal, shielding).</p></li><li><p style="min-height:1.5em"><strong>Supplier & Manufacturing Ramp-up</strong> - Qualify PCB manufacturers and assembly houses; support DFM/DFA review for production; manage NPI transitions.</p></li><li><p style="min-height:1.5em"><strong>Documentation</strong> - Maintain schematics, layout files, test procedures, and hardware specifications.</p></li></ul><p style="min-height:1.5em"></p><p style="min-height:1.5em">We look forward to hearing how you can help shape the future of autonomous defense systems at Harmattan AI.</p><p>Find <a href="https://www.arbeitnow.fr">Jobs in France</a> on Arbeitnow</a>